Guide · Homeowners · 4 min read · Updated 17 November 2026
Preparing for EV Charger Installation: What Happens on the Day
Short answer
To prepare for a home EV charger installation, send photos of your consumer unit, meter and charger location, agree the cable route, check Wi-Fi reaches the charger and clear access to the consumer unit. On the day, the electrician fits the unit, runs the circuit, sorts earthing, tests and certifies it and sets up the app. Expect the power to be off for part of the visit.
Before the survey
Most installations start with a remote survey using photos. Take clear pictures of the consumer unit with the cover on and the labels visible, the electricity meter, the main fuse carrier and the wall where you want the charger. A wider photo showing the driveway and house front helps the installer judge the cable route.
Note anything unusual: an extension built since the house was wired, a garage with its own supply, solar panels or a home battery. These all affect the design. If you are on an off-peak tariff, say which one, because the charger's schedule should match it.
- Photo of the consumer unit with labels visible
- Photo of the electricity meter and main fuse
- Photo of the intended charger location
- Wide photo of the driveway and front of the house
- Details of solar panels, batteries or outbuildings
Choosing where the charger goes
Pick a location that suits where you park and where the charging socket is on your car. Most cable lengths are around 5 to 7.5 metres. If you park nose-in and the socket is at the front, the charger should be near the front of the drive. Think about where a second car might park in future.
Avoid places where the cable would cross a path people walk along, or where cars could hit the unit. A wall close to the consumer unit keeps the cable run short and the cost down. Check that the wall is solid enough for fixings and not covered by a gas meter box or downpipe.
| Consideration | Why it matters |
|---|---|
| Car socket position | Cable must reach without stretching or trailing across paths |
| Distance to consumer unit | Shorter routes cost less and are quicker to install |
| Wi-Fi signal | Smart features need a reliable connection |
| Protection from impact | Chargers on exposed corners can be hit by vehicles |
| Future second car | Positioning can make sharing one charger easier |
Checks the electrician makes
On the day, the electrician confirms the supply rating, the main fuse size and the earthing arrangement. If you have a PME, or TN-C-S, supply, they check how the charger will be protected against supply faults. This may involve a charger with open-PEN detection or an earth rod. They also check the consumer unit has space and is suitable for the new circuit.
They may fit a CT clamp on the incoming supply. This lets the charger measure total household demand and reduce charging power when the house is busy, preventing the main fuse being overloaded. It is a common and inexpensive way to avoid supply upgrades.
If the consumer unit is old, has no space for a new circuit or uses outdated protection, the electrician may recommend replacing it or fitting a small separate enclosure for the charger. This is something a good photo survey should spot in advance, so the fixed price already reflects it rather than being added on the day.
What happens during installation
The charger is mounted on the wall and the cable route is prepared, which may involve drilling through walls, clipping cable along walls or running it through ducting. The electrician then connects the new circuit at the consumer unit or a separate enclosure, which requires the power to be switched off for a period. Fridges, freezers and computers may need attention.
Once connected, the circuit is tested, the charger is commissioned and connected to Wi-Fi or mobile data, and the app is set up. Most installers then ask you to plug in your car to confirm it charges. A standard installation usually takes half a day to a day.
- Clear access to the consumer unit and charger wall
- Move cars off the driveway if asked
- Have your Wi-Fi password ready
- Keep the car available for a test charge
- Plan for a short power outage
After the installation
You should receive an electrical installation certificate and, in England and Wales, confirmation that the work has been notified under the Building Regulations. The installer also notifies the network operator. Keep these documents with the charger warranty and your house paperwork.
Set up your charging schedule to match your tariff. The Electric Vehicles (Smart Charge Points) Regulations 2021 mean new chargers have default off-peak settings, but you can change them. Check the app regularly at first to make sure charging starts when expected, and contact the installer if anything seems wrong.
Common problems to avoid
The most frequent issue is a weak Wi-Fi signal at the charger, which stops smart features and scheduling working reliably. A Wi-Fi extender, mesh system or a charger with mobile data can solve it. Test your signal outside before installation day.
Another common problem is choosing a location that does not suit how you park, which leaves the cable stretched across the car. Take a few minutes to park as you normally would and imagine where the cable will run. If you have solar panels, make sure the installer knows, because solar-compatible set-up needs extra equipment.
Finally, think about cable storage. A tethered charger usually has a holster and hook, but cables left lying on the drive get run over and damaged. Coil the cable after each use and keep the connector clean and dry, which protects the pins and avoids charging faults.
Questions people also ask
Will my power be turned off during installation?
Yes, for part of the visit. The electrician needs to isolate the supply to connect the new circuit safely. This usually takes under an hour or two, depending on the consumer unit. Plan around it and check fridges and freezers stay closed.
Do I need to be at home for the installation?
Someone should be at home to give access to the consumer unit, confirm the charger location and receive the handover. You will also need to provide the Wi-Fi password and ideally have the car available for a test charge at the end of the visit.
What if my Wi-Fi does not reach the driveway?
A weak signal stops smart features working properly. A Wi-Fi extender or mesh system usually fixes it, or you can choose a charger with built-in mobile data. Test the signal at the charger location with your phone before installation day.
Written and checked by the EV Charger Installation team. Read our editorial policy.
More guides
How Much Does EV Charger Installation Cost in the UK?
A standard home 7kW smart EV charger installed in the UK costs £900–£1,400, including the charger, a dedicated circuit up to around 10 to 15 metres,…
EV Charger Installation Regulations in the UK Explained
EV charger circuits in the UK must be installed to BS 7671, including Section 722 for electric vehicle charging, and installers commonly follow the…
7kW vs 22kW EV Charger: Which Do You Need?
Most UK homes should choose a 7kW charger. Homes usually have a single-phase supply, which limits charging to around 7kW, and that is enough to fully…
Can You Install an EV Charger Without a Driveway?
You can only install a home charger where you have off-street parking you control, such as a driveway, garage or allocated bay. Without one, options…
Get a free ev charger installation quote
Tell us what you need and we'll come back with a clear price.
Request a quote