Guide · Homeowners and businesses · 4 min read · Updated 17 November 2026
EV Charger Installation Regulations in the UK Explained
Short answer
EV charger circuits in the UK must be installed to BS 7671, including Section 722 for electric vehicle charging, and installers commonly follow the IET Code of Practice. Most new home and workplace chargers must be smart under the Electric Vehicles (Smart Charge Points) Regulations 2021. In England and Wales a new charger circuit is notifiable work, and the network operator must be notified.
BS 7671 and Section 722
BS 7671, the IET Wiring Regulations, is the UK standard for electrical installations. Section 722 deals specifically with installations that supply electric vehicle charging. It covers how the circuit is protected, what residual current protection is needed and how earthing is arranged when a vehicle is connected outdoors.
In practice, it means each charger has its own dedicated circuit, suitable overcurrent protection and the right type of residual current protection. Many chargers include DC fault detection, which allows a Type A residual current device to be used on the circuit. Installers also refer to the IET Code of Practice for Electric Vehicle Charging Equipment Installation, which explains how to apply the rules in real installations.
Section 722 also deals with where the charging point sits and how it is protected against damage and the weather. An outdoor charger must suit its environment, with an appropriate ingress protection rating, and be positioned where it will not be struck by vehicles. Socket outlets and connectors must be placed so cables can reach the car without strain, and each charging point should be protected individually rather than sharing devices with other circuits.
- Dedicated circuit for each charge point
- Overcurrent protection sized for the charger and cable
- Residual current protection suited to the charger's DC fault detection
- Earthing arrangement assessed for outdoor vehicle connection
- Testing and an electrical installation certificate on completion
Earthing and the PME question
Many UK homes have a PME earthing arrangement, also known as TN-C-S. It is safe for normal use indoors, but a rare fault on the supply network can raise the voltage on earthed metalwork. Because a car outside is connected to the earth and people touch it while standing on the ground, BS 7671 requires extra measures for outdoor charging on PME supplies.
The common solutions are a charger with built-in open-PEN fault detection, which disconnects the car if a supply fault is detected, or a separate earth electrode for the charger, making that circuit a TT system. Which option is used depends on the charger, the property and the ground conditions. A good installer explains the choice rather than skipping it.
The smart charge point regulations
The Electric Vehicles (Smart Charge Points) Regulations 2021 apply to most new private charge points sold for home and workplace use in Great Britain. They require chargers to have smart functionality, such as the ability to send and receive information, respond to signals and shift charging to different times.
The rules also require default charging settings that avoid peak hours unless the user changes them, randomised start delays to reduce sudden demand on the network, and security protections for the device and its software. For customers, this mostly means choosing a compliant charger and setting the schedule in the app to suit your tariff.
| Requirement | What it means for you |
|---|---|
| Smart functionality | Charger connects to the internet and can be scheduled or controlled |
| Default off-peak settings | Charging avoids peak hours unless you override it |
| Randomised delay | Charging may start a few minutes after the scheduled time |
| Security requirements | Software and data protected against tampering |
| Continued charging if offline | The charger should still charge if it loses its connection |
Building regulations and notification
In England and Wales, installing a new circuit in a home is notifiable electrical work under the Building Regulations. That means it must either be self-certified by an electrician registered with a competent person scheme or approved by building control. The installer handles this, and you should receive a building regulations compliance certificate afterwards.
The network operator must also be notified when a charger is installed. Larger chargers, or installations where total demand is high, may need approval from the network operator before connection. A competent installer submits the notification and, where needed, the application. If you sell your home, the certificates show the work was done properly.
Approved Document S for new buildings
In England, Approved Document S of the Building Regulations covers infrastructure for charging electric vehicles. It requires charge points or cable routes for many new homes with associated parking, many new non-residential buildings with parking, and some buildings undergoing major renovation. It does not require existing homes to install chargers.
Developers, landlords and businesses planning new builds or major works should factor Approved Document S into early design, because it affects parking layouts and electrical capacity. Scotland and Wales have their own building standards and guidance, so check the rules for the relevant nation.
Planning, pavements and shared parking
Wall-mounted chargers on houses often fall under permitted development in England, subject to limits on size and location, but conservation areas, listed buildings and flats are treated differently. If you are unsure, check with your local planning authority before installation.
Running a charging cable across a public pavement is a separate issue. Trailing cables across the footway can create a trip hazard, and councils take different approaches. Some allow approved cable channels under specific schemes. Never run a cable across a pavement without checking your council's position first.
For businesses and landlords installing chargers in car parks, the layout of bays, bollards and cable routes also needs thought. Chargers should not block walkways or fire escape routes, and accessible bays should have chargers that can be reached by disabled drivers. Planning these points early avoids costly changes once groundwork has been done.
Questions people also ask
Can any electrician install an EV charger?
An electrician needs to be competent with the specific requirements of BS 7671 Section 722 and EV charging equipment. To self-certify the work in England and Wales, they must be registered with a competent person scheme. Many charger manufacturers also require installers to complete product training for warranty purposes.
Do I need planning permission for a home EV charger?
Often not. In England, a wall-mounted charger on a house is usually permitted development within size and location limits. Listed buildings, conservation areas and flats can be different, so check with your local planning authority if any of these apply.
What certificates should I get after installation?
You should receive an electrical installation certificate showing the circuit was tested to BS 7671, and a building regulations compliance certificate or building control completion. Keep both with your house documents, alongside the charger warranty and any network operator notification confirmation.
Written and checked by the EV Charger Installation team. Read our editorial policy.
More guides
How Much Does EV Charger Installation Cost in the UK?
A standard home 7kW smart EV charger installed in the UK costs £900–£1,400, including the charger, a dedicated circuit up to around 10 to 15 metres,…
7kW vs 22kW EV Charger: Which Do You Need?
Most UK homes should choose a 7kW charger. Homes usually have a single-phase supply, which limits charging to around 7kW, and that is enough to fully…
Can You Install an EV Charger Without a Driveway?
You can only install a home charger where you have off-street parking you control, such as a driveway, garage or allocated bay. Without one, options…
Preparing for EV Charger Installation: What Happens on the Day
To prepare for a home EV charger installation, send photos of your consumer unit, meter and charger location, agree the cable route, check Wi-Fi…
Get a free ev charger installation quote
Tell us what you need and we'll come back with a clear price.
Request a quote